Carbon Monoxide Gas Transmitter

Carbon Monoxide Gas Transmitter
Product Description

Carbon Monoxide Gas Detector


  • Industrial Standard, 4 - 20 mA O/P With Respect To Gas Concentration
  • Loop Test, Assures Proper Operation Of The Transmitter Without Calibration Gas
  • Power On Start up Through Intelligent Electronic, Self Driven Menu
  • Micro controller Based Software Calibration - No Trim Pots
  • Calibration Possible In Atmospheric Air
  • Easy Programming With Password Protection
  • Easy-to-read Display, Fast Response
  • Easy To Replace Sensor At The Field-plug-in Module
  • Built-in Reverse Polarity Protection
  • No Additional Power Required
  • Highly Reliable, Fast, Accurate For Specific Gas Detection
  • Excellent Long Term Stability
  • User Friendly, Simple To Operate & Easy To Install
  • Reduced Operating, Maintenance And Installation Cost,One Man Calibration
  • Suitable In Hazardous Area ATEX, CCOE, CMRI and lP-65 Approved
  • Ready To Use With Any DCS, PLC and AMBETRONICS Controllers
  • Digital Filter to smooth input signal


  • Car Parking Areas
  • Ambient Monitoring
  • Pulp and Paper Plants
  • Chemical and Petrochemical Plants
  • Acid Alkalizes and Dyes Mfg. Plants
  • Chemical Processing Plant
  • Offshore Drilling and Processing Platforms
  • Refineries
  • Stack Monitoring
  • Chemical Storage Area
  • Sewage Plants
  • Fertilizers Plants
  • Power and Industrial Plants
  • Gas Metering Station
  • Bullet Yard / Storage Yard
  • Oil and Gas industries
  • Coal Mine and Confined Area
  • Gas Pipeline Project



Oxygen / Toxic gases, Please select from the Table

Range / Resolution

As specified in the Table


± 2% of the full scale value

Sensor type

Electrochemical sensor, Imported make

I Sensor life

Expected 24 months

Loop output

Industrial standard 4-20mA DC O/P with permissible load 750 ohm at 24 VDC, 25mA


0.5, 31/2 digit LCD Display

Set point

Two independent set point, LO and HI with blinking indication with programmable latch and non-atch

Facility only for indication purpose. (There is no relay output)


Setting by 4 keys on front panel i.e. SET / NEXT, UP, DOWN AND TEST / BACK


By Display :Sensor Break/ Open / Over range / Under range Shows E r r Indication

By loop current : Up scale current : 22mA, Down scale current : 3.6mA to 3.9mA, Selectable

Supply Voltage

14VDC to 36VDC


1.5 sq. m 2 Core, Flexible OR Armoured shielded cable

Operating Temperature

0 to 50ºC 5%, Relative humidity: Below 95% non condensing

Sensor Housing

P.V.C. / P.P. / material / SS304 / 88316, Please specify While ordering

Enclosure Detail

GT-1000- WP (Weatherproof)

GT- 1000- FLP (Flameproof)

Protection Class


IP-65 for Gas Gr. IIA and IIB, CCOE and CMRI Approved

Cabinet Material

Polycarbonate, gray colour

Cast Alluminium alloy, LM-6 / (3.1. Enclosure

Cable Entry

1No, Themoplastic cable gland (IP 68)

No. Double compression cable gland (Ex-Proof), 3% ET type


190mm (H) x 80mm (W) x 55mm (D)

190mm (H) x 185mm (W) x 100mm (D)


Wall Mounting / Stand Mounting

Wall Mounting / Stand Mounting


250 Grams


Contact Us

17-B, Tarun Industrial Estate, Mogra Pada, New Nagardas Road, Andheri (East), Mumbai, Maharashtra, 400069, India
Phone :+918068090472